After applying polycrylic, I had to sand. I used the fine sandpaper with the sanding blocks to sand down the polycrylic and then I used the steel wool. To sand it smooth, I had to rub back and forth really fast. When I was done, the box was white and super smooth.
After I sanded, it was time to hinge. Since my box is so big, I had to put three instead of two hinges. The first step was to put my lid and base in a vise. Then I had to line the hinges up so that the barrels were lined up with the seam of my box. I also had to measure so that the hinges on the end were the same length away from the edge. When I knew exactly where I wanted my hinges to go, I put masking tape on one side of them so the wouldn’t move.
I had to first make a pilot hole with an awl. I had to place it in the center of the hole and tap it three times. When I had a small hole, I screwed the screw in with the screwdriver.
After gluing and sanding, I had to stain. I chose the dark walnut stain because I thought it was the perfect shade.
To stain, I had to use an apron and put on gloves. I first took a rag and folded it up. Then I dipped it a little in the stain. Next, I rubbed the stain around in circles. I stained my whole box besides the inside and it looked great.
The next step was to apply polycrylic. This would make my box shiny and resistant to water and scratches. I had to apply five thin coats of it and I had to wait five minutes in between each coat. The next step after applying polycrylic is sanding.
After sandingall the faces and edges of my wood, I had to glue everything together. First I would have to glue the sides together.
First, I had to put a small amount of glue in a line on the edge of my wood. Then I smudged it around with my finger so it was all evenly spread out. After I let it sit for a little bit, I took the other side and attached it. Then I put some masking tape on to keep it together. Then I glued the other two sides to the ones I just glued. If some of the glue seeped out, I took a wet paper towel to wipe it. Next, I had to put my four sided frame in a vise. I used cardboard as bumpers so the vise wouldn’t dent my wood.
After my wood dried the next day, I had to use the belt sander to sand the edges. It is a very powerful sander. After I sanded, I had to glue on my top and bottom. I did the same process where I put glue on the four edges and glue the wood on top. Then I put my box in a vise again with the cardboard bumpers.
The next day, I had to use the belt sander again to sand. After I did that, I used the palm sander to do some finish sanding. Since my box is so big, I couldn’t use the belt sander for sanding some of the edges and I had to use the palm sander instead. At first the sandpaper wasn’t rough enough to smooth the edges completely, but then I changed it to a new one and it worked. After I used the heavy sandpaper, I used the finer one to do some touch-ups. Then I was ready to stain.
After finishing all my cuts, I had to sand my wood. The cutting left some splintery edges that I needed to sand. I had to use a sanding board for the edges and sanding blocks for the face.
To use the sanding boards, I had to rub the edge or end of my wood against the sandpaper that was stapled to a board. I would go back and forth about 36 times on each edge.
After sanding all my edges until they are nice and smooth, I had to use the sanding blocks to smooth out the faces. I had to take a piece of sand paper and rap it around a block. Then I would back and forth on my wood. It was very important to only sand parallel to the grain. I didn’t want and scratches messing it up.
After I measuredmy wood, it was time to cut. First I would do my cross cuts, which were perpendicular to the grain. For this, I used the box saw.
The first step was to lift up the saw and carefully slide my wood under. The teeth of the saw should rest right on the line. Then I would use a bumper to put on top of my wood. Then I would clamp it down. The bumper keeps dents out of the wood. When cutting, I had to keep the saw level and I had to go back and forth.
After cross-cutting, I had to rip cut. Rip cuts were parallel to the grain. For this, I used the band saw.
You had to be very careful because the blade was very sharp and moving really fast. To cut, I had to line the blade up with my line. Then I turned on the machine and pushed the wood through the blade. I was careful not to have my fingers near it, and when I got close, I used a pusher tool/scrap piece to push the wood through.
Making the cardboard model helped me because I could then have an idea just how big it was going to be and if I wanted to change anything, which I did. Instead of the lid being on top, I wanted it to be on the front like a door. I also used it to compare my wood so I knew I wasn’t totally off.
I thought that using all the different tools was challenging, but very helpful. The t-squares were a bit hard to use because it was hard to check all of the angles where there was no where for it to hang. The rulers weren’t too hard to use. The box saws were a little tricky at first, but then I got the hang of it and I could make a very clean cut. The band saw was a little scary, so I’ll see how it turns out when I use it to rip the sides of my board.
While I was measuring, I faced some challenges. Every time I thought I measured the lines and the angles, I measured again and it turned out to be off by a lot. I had to re-measure many times to just get even one line right.
It was also a bit hard to cut the wood because it always got caught and it got hard to push back and forth. It was so satisfying when I finally cut it and the saw drops.
Out of everything, I think that measuring was the most frustrating thing.
My next steps are to cross cut my last two boards and to rip the sides of three of my boards. Then I will sand, glue, etc., but that will be later.
After I got my wood, I had to measure. To find the perpendicular edges on by boards, I had to use a t-square. That perpendicular edge would be the one that I use. I also had to use the t-square to draw my perpendicular lines. I would put my ruler on top of it and trace a line that was the right length.
Now that I finished my model, it was time to conference and get my wood. My measurements would have to change a bit because the width of the board was 1/2 inch. Instead of 2 12×9 boards, 2 8×9 boards, and 2 8×12 boards, I would get 2 12×9 boards, 2 7×8 boards, and 2 7×12 boards. My wood plank was going to be very big.
My box model will be made out of cardboard. The first step is measuring the faces and tracing them on the cardboard. Since my box is really big, I needed five pieces of cardboard. After I measured and traced my pieces, I had to cut them with a scroll saw.
After I cut all my pieces out, I had to tape it all together. I didn’t completely tape the top because I wanted it to be like a hinge. I did that by putting tape on one side and on the front and back.
Now that I had my model, I put it in my locker so I would be sure everything would fit.
Our first project in Tech 7 is making a box. The first step is making a plan. I wanted my box to be unique because almost everyone made there’s the same. Mine was going to be very big.
The only requirement was that it had to fit in my locker. It wasn’t that big, so I measured it so my box would be almost as big as the locker. At first, I wanted it to be 16” x 12” x 9”. When I told my teacher, she said that there has to be room to separate the pieces when they are wet. Instead of being 16” long, I changed it to 8” long. That would give a perfect amount of room for wet pieces.